INDUSTRA-GLOSS SB
Is a high performance proprietary formulation of Methyl methacrylate
copolymer resin in a solvent base.
Can be used as a hardener, cure, sealer and as a stain resistant
surface protector.
INDUSTRA-GLOSS SB is excellent for exterior and interior on
most horizontal and vertical surfaces. Especially - Travertine Stone
pavers
Driveways | Patios | Pavers | Stamped concrete | Garages | Showrooms
| Exposed aggregate | Decorative Concrete
Application Techniques Surface Preparation
Apply INDUSTRA-GLOSS SB in a uniform, continuous film by airless
sprayer, short napped mohair roller, lambs wool applicator, paintbrush,
or soft bristled push broom.
Freshly Placed Concrete: Apply a full, light to medium even coat
of INDUSTRA-GLOSS SB to ensure complete, uniform coverage of the surface.
Use a lambs wool applicator or roller to pick up puddles or excess
material. A second coat may be applied depending upon protection and
surface gloss desired. The second coat should be applied as soon as
the first coat has dried.
Existing Concrete: Apply a uniform film of INDUSTRA-GLOSS SB. Apply
a second coat, if desired, as soon as the first coat has dried. Full
cure will occur overnight and maximum hardness will be achieved in
appx. 5-7 days.
FEATURES AND BENEFITS
" Non-yellowing
" Dustproof, protects, decorates
" Reduces spalling
" VOC compliant
" Easily cleaned
" Abrasion resistant
" Complies with ASTM C1315 and ASTM C309
" Provides glossy, "wet" look
SURFACE PREPARATION:
Existing Concrete: When used as a sealer the surface must be structurally
sound, free of dust, dirt, mortar residue, curing and form release
compounds and all other contaminants. Prior to application, all surface
defects, cracks, voids and joints must be properly filled and allowed
to cure per manufacturers recommendations. A dry substrate offers
better product penetration than a damp surface.
Freshly Placed Concrete: Horizontal surface must be finished and
the surface "moisture" sheen should have disappeared. The
surface must be able to withstand foot traffic from workmen. Vertical
surfaces may be treated as soon as the forms have been removed and
the surface rubbed.
MATERIAL PROPERTIES @ 75°F., 50% R.H.
Weight per gallon, lbs 7.5
Viscosity, cps 250
TUKON Hardness >10
Flash Point, F 110
ASTM C1315 test results >10
Coverage rate, sq. ft./gal 300
Solids, % >25%
Dry time, hrs. 1- 3
UV exposure Meets class A Requirements
Water loss, kg/m2 <. 35
Acid/Alkali resistance Meets Requirements
The following coverage rates are approximate and for estimating purposes
only. Make test applications on actual surfaces to determine exact
coverage rates.
Additional coats will enhance performance and appearance.
Appx. Sq/ft p/gal
As a cure and seal 200-250
On existing concrete 200-400
2nd & 3rd coats * 250-400
Most surfaces will go 200 sq ft per gal for the first coat and 300
for the second. If longer term benefits are desired it is highly suggested
to do at least two coats with any surface product such as this.
* ADDITIONAL COATS WILL YIELD A HIGHER GLOSS AND ENHANCE OVERALL
PROTECTION
MIXING INSTRUCTIONS:
INDUSTRA-GLOSS SB does not require mixing. Do not thin or dilute.
Clean-Up
CLEAN-UP INSTRUCTIONS:
Clean tools and equipment with aromatic 100
or xylene immediately following use. Clean
drips and over spray with solvent while still
wet. If not cleaned immediately, the sealer may
leave a residue on painted surfaces, glass or wood.
Packaging
INDUSTRA-GLOSS SB is available in 5 gal and 55 containers.
Storage: 50 - 800F. Protect from freezing. Shelf-Life: 2 year, in
protected storage.
Environmental & Safety Cautions
INDUSTRA-GLOSS SB contains petroleum distillates and is combustible.
Keep away from heat, sparks and open flame. Keep containers closed
until ready to use. Provide adequate ventilation. To prevent vapor
build up and possible explosion, open all doors and windows and provide
cross ventilation. Do not smoke. Solvent vapors can cause respiratory
irritation. For respiratory problems, remove person immediately to
fresh air. Contact may cause skin or eye irritation. Using respiratory
devices, safety goggles and impervious gloves is recommended.
Wash hands thoroughly with soap and water after handling and before
eating or smoking. If ingested, do not induce vomiting and call a
physician immediately. For eye contact, flush immediately with water
for 15 minutes and consult a physician immediately. Do not rub eyes.
Protect shrubbery, plants and grass during application. Protect asphalt,
rubber and plastic surfaces from spills and over spray.
READ MATERIAL SAFETY DATA SHEET BEFORE USING. MATERIAL IS FOR INDUSTRIAL
USE ONLY. KEEP AWAY FROM CHILDREN AND ANIMALS. EMERGENCY RESPONSE
PHONE NUMBERS ARE (877) 738-7325 V-SEAL OR (800) 424-300 CHEMTREC
INDUSTRA-GLOSS SB is not recommended to seal voids, cracks or for
use where severe hydrostatic pressure is present. Do not apply to
exterior surfaces if rain is expected within 12 hours after application
or in direct sunlight at ambient temperatures in excess of 90°F.
The sealer may darken the surface and may accentuate surface imperfections.
Always do a test application to evaluate appearance and performance.
The coefficient of friction of the surface may decline with each sealer
application.
Do not apply to frozen or frost filled surfaces.
Not recommended for asphalt surfaces. Certain water-based tile adhesives
may not bond to INDUSTRA-GLOSS SB. Always apply test area to confirm
adhesion.